Mark My Words – October: Bearings, Generators, Long-Term Parking, Water Heaters and Tire Problems

author image

October 22, 2018

Mark My Words - Easy Fixes to Common RV Problems - Mark NemethHi, folks. This month we’ll talk about bearings, generators, long term parking, water heaters and tire problems. Remember, you can submit your RVing questions to [email protected]. Happy Trails!

———————————————

Mark:

How often should you repack your wheel bearings on a travel trailer? I am hearing once a year. Is this correct? I can do myself but was wondering is there a video or something that can walk a person through this, as taking it to an RV dealer is rather expensive yearly. Thanks, Nolan

Hi, Nolan:

If your trailer is only used a few weekends a year and is never submerged in water (like a boat trailer), you can probably go quite a bit longer than one year before you need to worry too much about repacking the bearings. If you travel extensively, like 20K – 30K miles per year, the one-year interval is a good idea. Even if the bearings are fine, pulling the hub and drum allows you to inspect the brake components for wear. Repacking bearings is not really all that difficult, but it can be really messy! Basically, you need to raise the wheel off the ground, remove it, and then remove the hub/brake drum assembly to gain access to the bearings. Check out http://www.etrailer.com/faq-wheelbearingpack.aspx for a step-by-step guide. There are also a number of videos available in their Help section. When reassembling the hub, it is important to properly set the preload on the bearings and then replace the nut retainer and/or cotter pin to keep everything together. You should also adjust and test the brakes after everything is back together. Like any other repair project, if you feel it might be beyond your capabilities, please take it to a service facility and have a qualified tech do the work.

———————————————

Hi, Mark:

My generator runs fine at low elevation, but when I go to higher elevations, it won’t run properly.  I’ve adjusted the elevation level thing on the carburetor, but sometimes it won’t stay running.  Can you explain why?  Thanks, Ralph

Hi, Ralph:

Several possibilities come to mind. When you operate carbureted engines at high altitude, there is essentially less air density, so they tend to run rich. The altitude adjustment on your generator is designed to manually compensate for that effect by allowing you to lean out the fuel mixture. However, if your generator carburetor is not in good adjustment or is gummed up with fuel deposits or sludge, the altitude adjustment may not be effective. That’s why it is so important to exercise the generator at least once a month, under load, for at least 30 minutes. This exercise is needed to keep the fuel system clean and everything limbered up. Another possibility is that you are inadvertently overloading your generator when you are at high altitude by expecting it to run everything as well as it does “down below.” Your generator can’t operate the same AC load at high altitude that it can at sea level. Most engines lose about 3-4 percent of their rated horsepower per each 1,000-foot increase in altitude. At 6,000 feet, that could reduce your generator’s horsepower by as much as 20 percent! Your generator operator’s manual will have a chart that specifies how much the unit should be de-rated for increases in operating altitude.

——————————————-

Dear Mark:

I have moved my Alfa Gold, 35-ft. 5th-wheel with 2 slide-outs, to a park and plan to live in it for a few years.  I live alone and can do a lot of the maintenance things myself but will definitely need help with anything up on the roof.  I will not be moving the trailer in and out of my space.  I have covers for the wheels and plan to use heavy-duty jacks to stabilize the trailer in four places.  What I need to know is: Are the jacks a good idea and, if yes, exactly where should they be placed? Also, how large and what kind of a weight distribution pad should I have between the jack and trailer bottom? Is there additional maintenance required for a trailer that stays in place? Thanks for any info you can provide.   Nancy

Hi, Nancy:

You can certainly use jacks if you wish; just be sure that the jacks are positioned so that the lift is applied only to the trailer’s frame. If desired, you can use a block of pressure-treated wood between the jack and the frame. A piece of 4×4 works well for this. Do not try to support the trailer by any part of the body, as it’s not strong enough. Since you have a 5th-wheel, I strongly suggest that you consider a 5th-wheel stabilizer tripod for the front of the rig. Here’s an example of what I’m referring to: http://www.pplmotorhomes.com/parts/rv-jacks/stabilizer-jacks-5th-wheel.htm

Using one of these stabilizers will significantly reduce sway and bounce, and if your rig also has standard stabilizing jacks on the rear, you may not need any additional jacks. As far as additional maintenance goes, there’s really not a lot you would need to do with a parked trailer. Keep the tires covered and inflated, keep up with roof maintenance, and continue to keep the black-tank valve closed at all times, dumping the tank only when it is nearly full.

——————————————

Hi:

We have an older travel trailer with a Suburban 6-gallon water heater.  It is one that does not have an automatic ignition, so we have to light the pilot whenever we need hot water.  The problem is when the burner ignites; it causes a small “explosion” and sometimes blows out the pilot. Of course, it then needs to be re-lit.  This occurs only intermittently when the main burner ignites and does not seem to be dependent on wind or weather.  I have noticed no gas smell inside or outside.  The gas system has been leak- and pressure-tested and a new regulator installed, but no joy. Any ideas? Ron

Hi, Ron:

Most water heater pops and explosions are caused by a delay in igniting the main burner when gas starts to flow. When the main burner valve opens and ignition is delayed, propane can collect in the combustion tube and create a pop or bang when it is finally ignited. This problem is more common with DSI heaters, the ones that use an electric spark to light the burner. I suggest that you inspect the burner, burner tube, and combustion chamber to be sure there are no obstructions. Spiders and mud daubers’ nests in any of these areas can cause erratic operation. Also, make sure that the pilot flame is at least ½” long and is blue and conical in shape. If the pilot is too low or weak, it may not properly ignite the main burner. If the pilot looks wrong or if the heater continues to act up, have a qualified technician take a look at it. There could be a problem with the gas control valve or pilot valve.

————————————-

Mark:

I have an 18-ft. travel trailer that runs with only two tires.  I have towed it only 4,000 miles and had a flat tire twice.  The trailer originally came with ST185 tires and now wears ST175 tires.  What would be the best way to prevent frequent flat tires? Masako

Hi, Masako:

It’s critical to know what your trailer weighs!  You need to take the trailer, with all of the items you would normally carry onboard, to a scale and weigh it. Once you know how much weight is on your tires, check the sidewall weight rating to be sure that the tires are rated to carry the load. You can check the RV’s rating plate, owner’s manual, or other documentation to see what tires the manufacturer recommends, but knowing your weight is the most important piece to the puzzle. Proper inflation is also a key element for tire life. The proper inflation pressure for any tire is actually determined by the weight it is carrying, and the “max pressure” is often not the best operating pressure. Most tire manufacturers have pressure charts that provide this information on their websites, usually referred to as load/inflation tables. However, you’ll need to know the actual weight each wheel is carrying on your rig in order to use these tables. The best way to get that information is usually at an RV rally where individual wheel weighing is being offered. There are several groups offering this specialized weighing, one is the Escapees SmartWeigh program www.escapees.com/smartweigh  Be sure to check your tire pressure before the start of each trip and each morning before you hit the road while traveling. Once you have the correct tires for the load and keep them properly inflated, your tire problems should be minimized.

EscapeesFounded in 1978, the Escapees RV Club provides a total support network that includes a wide variety of services and opportunities:

  • Mail Service- Escapees offers the largest private mail service in the country. Members are able to personalize their mail delivery with multiple options. Custom sorting options, delivery schedule and even mail scanning. We make it easy!
  • Mapping Tool- Plug in your starting point and destination, and let us do the rest! Our mapping tool will show you discount parks along your route, as well as trusted commercial members and endorsed vendors to help you with all of your needs along the way.
  • Education- From our annual Escapades to our discussion forum, we help you connect with fellow RVers to share experience and knowledge. For the hands-on learner, RVers’ Boot Camp is a great way to learn about RV operation, safety and maintenance. Our award-winning magazine is also a great resource for peer-to-peer advice from fellow RVers and industry experts.
  • Community- When you see an Escapees sticker on a rig, you know you’ve found a friend. Escapees hosts a variety of events throughout the year, including convergences, excursions, chapter rallies and Escapade. Each of these offers the opportunity to connect with other RVers and make new friends.

A complete listing of all Escapees events and a comprehensive list of member benefits are found at www.escapees.com

Leave a Reply

3 comments

  1. Anonymous

    Great topics and well read articles…Very much needed information for myself!

  2. Anonymous

    Great articles thanks for sharing your knowledge

  3. Anonymous

    Great information. Thanks.